View NLSX5002_7864034.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? semiconductor components industries, llc, 2012 april, 2012 ? rev. 0 1 publication order number: NLSX5002/d NLSX5002 2-bit 100 mb/s configurable dual-supply level translator the NLSX5002 is a 2-bit configurable dual-supply autosensing bidirectional level translator that does not require a direction control pin. the i/o v cc - and i/o v l -ports are designed to track two different power supply rails, v cc and v l respectively. both the v cc and the v l supply rails are configurable from 0.9 v to 4.5 v. this allows a logic signal on the v l side to be translated to either a higher or a lower logic signal voltage on the v cc side, and vice-versa. the NLSX5002 offers the feature that the values of the v cc and v l supplies are independent. design flexibility is maximized because v l can be set to a value either greater than or less than the v cc supply. in contrast, the majority of competitive auto sense translators have a restriction that the value of the v l supply must be equal to less than (v cc - 0.4) v. the NLSX5002 has high output current capability, which allows the translator to drive high capacitive loads such as most high frequency emi filters. another feature of the NLSX5002 is that each i/o_v ln and i/o_v ccn channel can function as either an input or an output. an output enable (en) input is available to reduce the power consumption. the en pin can be used to disable both i/o ports by putting them in 3-state which significantly reduces the supply current from both v cc and v l . the en signal is referenced to the v l supply. features ? wide v cc , v l operating range: 0.9 v to 4.5 v ? v l and v cc are independent ? v l may be greater than, equal to, or less than v cc ? high ? speed with 140 mb/s guaranteed date rate for v cc , v l > 1.8 v ? low bit ? to ? bit skew ? overvoltage tolerant enable and i/o pins ? non ? preferential power ? up sequencing ? power ? off protection ? small packaging: uqfn8, 1.4 mm x 1.2 mm, 0.4 mm pitch ? these devices are pb ? free and are rohs compliant typical applications ? mobile phones, pdas, other portable devices important information ? esd protection for all pins: ? hbm (human body model) > 8000 v ? mm (machine model) > 400 v http://onsemi.com ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our tape and reel packaging specification brochure, brd801 1/d. uqfn8 mu suffix case 523as marking diagram device package shipping ? ordering information NLSX5002bmutcg uqfn8 (pb ? free) 3000/t ape & reel am 1 a = specific device code m = date code
NLSX5002 http://onsemi.com 2 figure 1. t ypical application circuit i/o v l 1 i/o v l n en oe i/on i/o1 gnd +1.8 v system +1.8v +3.6v +3.6 v system i/on i/o1 gnd gnd NLSX5002 i/o v cc 1 i/o v cc n v l v cc figure 2. simplified functional diagram (1 i/o line) p one ? shot n one ? shot p one ? shot n one ? shot v l i/o v l i/o v cc v cc r1 r2 figure 3. application example for v l < v cc en ano c 2.5 v 3.0 v peripheral gnd NLSX5002 v l v cc i/o v l 2 i/o v cc 2 rx tx i/o v l 1 i/o v cc 1 tx rx figure 4. application example for v l > v cc en ano c 2.5 v 1.8 v peripheral gnd NLSX5002 v l v cc i/o v l 2 i/o v cc 2 rx tx i/o v l 1 i/o v cc 1 tx rx
NLSX5002 http://onsemi.com 3 figure 5. logic diagram v l v cc gnd en i/o v l 1 i/o v l 2 i/o v cc 1 i/o v cc 2 figure 6. pin assignments uqfn8 (top view) v cc i/o v cc 1 i/o v cc 2 en v l i/o v l 1 i/o v l 2 gnd 1 5 2 3 4 8 7 6 pin assignment pins description v cc v cc input v oltage v l v l input v oltage gnd ground en output enable i/o v cc n i/o port, referenced to v cc i/o v l n i/o port, referenced to v l function table en operating mode l hi ? z h i/o buses connected
NLSX5002 http://onsemi.com 4 maximum ratings symbol parameter value condition unit v cc i/o v cc ? side dc supply v oltage ? 0.5 to +5.5 v v l i/o v l ? side dc supply v oltage ? 0.5 to +5.5 v i/o v cc v cc ? referenced dc input/output v oltage ? 0.5 to +5.5 v i/o v l v l ? referenced dc input/output v oltage ? 0.5 to +5.5 v v i enable control pin dc input v oltage ? 0.5 to +5.5 v i ik dc input diode current ? 50 v i < gnd ma i ok dc output diode current ? 50 v o < gnd ma i cc dc supply current through v cc 100 ma i l dc supply current through v l 100 ma i gnd dc ground current through ground pin 100 ma t stg storage t emperature ? 65 to +150 c stresses exceeding maximum ratings may damage the device. maximum ratings are stress ratings only. functional operation above t he recommended operating conditions is not implied. extended exposure to stresses above the recommended operating conditions may af fect device reliability. recommended opera ting conditions symbol parameter min max unit v cc i/o v cc ? side positive dc supply v oltage 0.9 4.5 v v l i/o v l ? side positive dc supply v oltage 0.9 4.5 v v i enable control pin voltage (referenced to v l ) gnd 4.5 v v io bus input/output v oltage i/o v cc i/o v l gnd gnd 4.5 4.5 v t a operating temperature range ? 55 +125 c t/ v input transition rise or rate v i , v io from 30% to 70% of v cc ; v cc = 3.3 v 0.3 v 0 10 ns
NLSX5002 http://onsemi.com 5 dc electrical characteristics symbol parameter test conditions (note 1) v cc (v) (note 2) v l (v) (note 3) ? 40 c to +85 c ? 55 c to +125 c unit min typ (note 4) max min max v ihc i/o v cc input high voltage 0.9 ? 4.5 0.9 ? 4.5 2/3 * v cc ? ? 2/3 * v cc ? v v ilc i/o v cc input low v oltage 0.9 ? 4.5 0.9 ? 4.5 ? ? 1/3 * v cc ? 1/3 * v cc v v ihl i/o v l input high voltage 0.9 ? 4.5 0.9 ? 4.5 2/3 * v l ? ? 2/3 * v l ? v v ill i/o v l input low v oltage 0.9 ? 4.5 0.9 ? 4.5 ? ? 1/3 * v l ? 1/3 * v l v v ih control pin input high voltage t a = +25 c 0.9 ? 4.5 0.9 ? 4.5 2/3 * v l ? ? 2/3 * v l ? v v il control pin input low voltage t a = +25 c 0.9 ? 4.5 0.9 ? 4.5 ? ? 1/3 * v l ? 1/3 * v l v v ohc i/o v cc output high voltage i/o v cc source current = 20 a 0.9 ? 4.5 0.9 ? 4.5 0.9 * v cc ? ? 0.9 * v cc ? v v olc i/o v cc output low voltage i/o v cc sink current = 20 a 0.9 ? 4.5 0.9 ? 4.5 ? ? 0.2 ? 0.2 v v ohl i/o v l output high voltage i/o v l source current = 20 a 0.9 ? 4.5 0.9 ? 4.5 0.9 * v l ? ? 0.9 * v l ? v v oll i/o v l output low voltage i/o v l sink current = 20 a 0.9 ? 4.5 0.9 ? 4.5 ? ? 0.2 ? 0.2 v i qvcc v cc supply current en = v l , i o = 0 a, (i/o v cc = 0 v, i/o v l = 0 v) or (i/o v cc = v cc , i/o v l = v l ) 0.9 ? 4.5 0.9 ? 4.5 ? ? 1 ? 2.5 a i qvl v l supply current 0.9 ? 4.5 0.9 ? 4.5 ? ? 1 ? 2.5 a i ts ? vcc v cc tristate output mode supply current t a = +25 c, en = 0 v 0.9 ? 4.5 0.9 ? 4.5 ? ? 1 ? 2.1 a i ts ? vl v l tristate output mode supply current t a = +25 c, en = 0 v 0.9 ? 4.5 0.9 ? 4.5 ? ? 1 ? 2.1 a i oz i/o tristate output mode leakage current t a = +25 c, en = 0v 0.9 ? 4.5 0.9 ? 4.5 ? ? 1 ? 1.5 a i i control pin input current t a = +25 c 0.9 ? 4.5 0.9 ? 4.5 ? ? 1 ? 1 a i off power off leakage current i/o v cc = 0 to 4.5v, 0 0 ? ? 1 ? 1.5 a i/o v l = 0 to 4.5 v 0.9 ? 4.5 0 ? ? 1 ? 1.5 0 0.9 ? 4.5 ? ? 1 ? 1.5 1. normal test conditions are v i = 0 v, c iovcc 15 pf and c iovl 15 pf, unless otherwise specified. 2. v cc is the supply voltage associated with the i/o v cc port, and v cc ranges from +0.9 v to 4.5 v under normal operating conditions. 3. v l is the supply voltage associated with the i/o v l port, and v l ranges from +0.9 v to 4.5 v under normal operating conditions. 4. typical values are for v cc = +2.8 v, v l = +1.8 v and t a = +25 c. all units are production tested at t a = +25 c. limits over the operating temperature range are guaranteed by design.
NLSX5002 http://onsemi.com 6 timing characteristics symbol parameter test conditions (note 5) v cc (v) (note 6) v l (v) (note 7) ? 55 c to +125 c unit min typ (note 8) max t r ? vcc i/o v cc rise time c iovcc = 15 pf 0.9 ? 4.5 0.9 ? 4.5 ? ? 8.5 ns 1.8 ? 4.5 1.8 ? 4.5 ? ? 3.5 t f ? vcc i/o v cc fall time c iovcc = 15 pf 0.9 ? 4.5 0.9 ? 4.5 ? ? 8.5 ns 1.8 ? 4.5 1.8 ? 4.5 ? ? 3.5 t r ? vl i/o v l rise time c iovl = 15 pf 0.9 ? 4.5 0.9 ? 4.5 ? ? 8.5 ns 1.8 ? 4.5 1.8 ? 4.5 ? ? 3.5 t f ? vl i/o v l fall time c iovl = 15 pf 0.9 ? 4.5 0.9 ? 4.5 ? ? 8.5 ns 1.8 ? 4.5 1.8 ? 4.5 ? ? 3.5 z ovcc i/o v cc one ? shot output impedance 0.9 1.8 4.5 0.9 ? 4.5 ? ? ? 37 20 6.0 ? ? ? z ovl i/o v l one ? shot out- put impedance 0.9 ? 4.5 0.9 1.8 4.5 ? ? ? 37 20 6.0 ? ? ? t pd_vl ? vcc propagation delay (driving i/o v cc ) c iovcc = 25 pf 0.9 ? 4.5 0.9 ? 4.5 ? ? 40 ns 1.8 ? 4.5 1.8 ? 4.5 ? ? 13 t pd_vcc ? vl propagation delay (driving i/o v l ) c iovl = 25 pf 0.9 ? 4.5 0.9 ? 4.5 ? ? 40 ns 1.8 ? 4.5 1.8 ? 4.5 ? ? 13 t sk channel ? to ? channel skew c iovcc = 15 pf, c iovl = 15 pf (note 9) 0.9 ? 4.5 0.9 ? 4.5 ? ? 0.15 ns i in_peak input driver maximum peak current en = v l ; i/o_v cc = 1 mhz square w ave, amplitude = v cc , or i/o_v l = 1 mhz square w ave, amplitude = v l 0.9 ? 4.5 0.9 ? 4.5 ? ? 5.0 ma 5. normal test conditions are v i = 0 v, c iovcc 15 pf and c iovl 15 pf, unless otherwise specified. 6. v cc is the supply voltage associated with the i/o v cc port, and v cc ranges from +0.9 v to 4.5 v under normal operating conditions. 7. v l is the supply voltage associated with the i/o v l port, and v l ranges from +0.9 v to 4.5 v under normal operating conditions. 8. typical values are for v cc = +2.8 v, v l = +1.8 v and t a = +25 c. all units are production tested at t a = +25 c. limits over the operating temperature range are guaranteed by design. 9. guaranteed by design.
NLSX5002 http://onsemi.com 7 timing characteristics (continued) symbol parameter test conditions (note 10) v cc (v) (note 11) v l (v) (note 12) ? 55 c to +125 c unit min typ (note 13) max t en ? vcc i/o_v cc output enable time t pzh c iovcc = 15 pf, i/o_v l = v l 0.9 ? 4.5 0.9 ? 4.5 ? ? 160 ns t pzl c iovcc = 15 pf, i/o_v l = 0 v 0.9 ? 4.5 0.9 ? 4.5 ? ? 130 t en ? vl i/o_v l output enable time t pzh c iovl = 15 pf, i/o_v cc = v cc 0.9 ? 4.5 0.9 ? 4.5 ? ? 160 ns t pzl c iovl = 15 pf, i/o_v cc = 0 v 0.9 ? 4.5 0.9 ? 4.5 ? ? 130 t dis ? vcc i/o_v cc output disable time t phz c iovcc = 15 pf, i/o_v l = v l 0.9 ? 4.5 0.9 ? 4.5 ? ? 210 ns t plz c iovcc = 15 pf, i/o_v l = 0 v 0.9 ? 4.5 0.9 ? 4.5 ? ? 175 t dis ? vl i/o_v l output disable time t phz c iovl = 15 pf, i/o_v cc = v cc 0.9 ? 4.5 0.9 ? 4.5 ? ? 210 ns t plz c iovl = 15 pf, i/o_v cc = 0 v 0.9 ? 4.5 0.9 ? 4.5 ? ? 175 mdr maximum data rate c io = 15 pf 0.9 ? 4.5 0.9 ? 4.5 50 ? ? mbps 1.8 ? 4.5 1.8 ? 4.5 140 ? ? 10. normal test conditions are v i = 0 v, c iovcc 15 pf and c iovl 15 pf, unless otherwise specified. 11. v cc is the supply voltage associated with the i/o v cc port, and v cc ranges from +0.9 v to 4.5 v under normal operating conditions. 12. v l is the supply voltage associated with the i/o v l port, and v l ranges from +0.9 v to 4.5 v under normal operating conditions. 13. typical values are for v cc = +3.3 v, v l = +1.8 v and t a = +25 c. all units are production tested at t a = +25 c. limits over the operating temperature range are guaranteed by design.
NLSX5002 http://onsemi.com 8 dynamic power consumption (t a = +25 c) symbol parameter test conditions v cc (v) (note 14) v l (v) (note 15) typ (note 16) unit c pd_vl power dissipation capacitance (referred to v l ) v l = input port, v cc = output port c load = 0, f = 1 mhz, en = v l (output enabled) 0.9 4.5 13 pf 1.5 1.8 7.0 1.8 1.5 6.0 1.8 1.8 6.0 1.8 2.8 7.0 2.5 2.5 6.0 2.8 1.8 6.0 4.5 0.9 10 v cc = input port, v l = output port c load = 0, f = 1 mhz, en = v l (output enabled) 0.9 4.5 19 pf 1.5 1.8 16 1.8 1.5 16 1.8 1.8 16 1.8 2.8 16 2.5 2.5 16 2.8 1.8 16 4.5 0.9 16 c pd_vcc power dissipation capacitance (referred to v cc ) v l = input port, v cc = output port c load = 0, f = 1 mhz, en = v l (output enabled) 0.9 4.5 16 pf 1.5 1.8 17 1.8 1.5 17 1.8 1.8 17 1.8 2.8 17 2.5 2.5 18 2.8 1.8 18 4.5 0.9 21 v cc = input port, v l = output port c load = 0, f = 1 mhz, en = v l (output enabled) 0.9 4.5 13 pf 1.5 1.8 6.0 1.8 1.5 7.0 1.8 1.8 7.0 1.8 2.8 6.0 2.5 2.5 7.0 2.8 1.8 7.0 4.5 0.9 15 14. v cc is the supply voltage associated with the i/o v cc port, and v cc ranges from +0.9 v to 4.5 v under normal operating conditions. 15. v l is the supply voltage associated with the i/o v l port, and v l ranges from +0.9 v to 4.5 v under normal operating conditions. 16. typical values are at t a = +25 c. 17. c pd vl and c pd vcc are defined as the value of the ic?s equivalent capacitance from which the operating current can be calculated for the v l and v cc power supplies, respectively. i cc = i cc (dynamic) + i cc (static) i cc (operating) c pd x v cc x f in x n sw where i cc = i cc_vcc + i cc vl and n sw = total number of outputs switching.
NLSX5002 http://onsemi.com 9 static power consumption (t a = +25 c) symbol parameter test conditions v cc (v) (note 18) v l (v) (note 19) typ (note 20) unit c pd_vl power dissipation capacitance (referred to v l ) v l = input port, v cc = output port c load = 0, f = 1 mhz, en = gnd (outputs disabled) 0.9 4.5 0.01 pf 1.5 1.8 0.01 1.8 1.5 0.01 1.8 1.8 0.01 1.8 2.8 0.01 2.5 2.5 0.01 2.8 1.8 0.01 4.5 0.9 0.01 v cc = input port, v l = output port c load = 0, f = 1 mhz, en = gnd (outputs disabled) 0.9 4.5 0.01 pf 1.5 1.8 0.01 1.8 1.5 0.01 1.8 1.8 0.01 1.8 2.8 0.01 2.5 2.5 0.01 2.8 1.8 0.01 4.5 0.9 0.01 c pd_vcc power dissipation capacitance (referred to v cc ) v l = input port, v cc = output port c load = 0, f = 1 mhz, en = gnd (outputs disabled) 0.9 4.5 0.01 pf 1.5 1.8 0.01 1.8 1.5 0.01 1.8 1.8 0.01 1.8 2.8 0.01 2.5 2.5 0.01 2.8 1.8 0.01 4.5 0.9 0.01 v cc = input port, v l = output port c load = 0, f = 1 mhz, en = gnd (outputs disabled) 0.9 4.5 0.01 pf 1.5 1.8 0.01 1.8 1.5 0.01 1.8 1.8 0.01 1.8 2.8 0.01 2.5 2.5 0.01 2.8 1.8 0.01 4.5 0.9 0.01 18. v cc is the supply voltage associated with the i/o v cc port, and v cc ranges from +0.9 v to 4.5 v under normal operating conditions. 19. v l is the supply voltage associated with the i/o v l port, and v l ranges from +0.9 v to 4.5 v under normal operating conditions. 20. typical values are at t a = +25 c
NLSX5002 http://onsemi.com 10 NLSX5002 en i/o v l v l v cc c iovcc t rise/fall 3 ns i/o v l i/o v cc t pd_vl ? vcc 90% 50% 10% 90% 50% 10% t pd_vl ? vcc t f ? vcc t r ? vcc figure 7. driving i/o v cc test circuit and timing i/o v cc NLSX5002 en i/o v l v l v cc c iovl source t rise/fall 3 ns i/o v cc i/o v l t pd_vcc ? vl 90% 50% 10% 90% 50% 10% t pd_vcc ? vl t f ? vl t r ? vl figure 8. driving i/o v l test circuit and timing i/o v cc source open pulse generator r t dut v cc r l r 1 c l 2xv cc test switch t pzh , t phz open t pzl , t plz 2 x v cc c l = 15 pf or equivalent (includes jig and probe capacitance) r l = r 1 = 50 k or equivalent r t = z out of pulse generator (typically 50 ) figure 9. test circuit for enable/disable time measurement v cc gnd t f t r 10% 50% 90% 10% 50% 90% t r t plh t phl t f 50% 50% 90% 10% t pzl t plz t pzh t phz gnd high impedance v ol v oh high impedance figure 10. timing definitions for propagation delays and enable/disable measurement en input 50% v l output output output
NLSX5002 http://onsemi.com 11 important applications information level translator architecture the NLSX5002 auto ? sense translator provides bi ? directional logic voltage level shifting to transfer data in multiple supply voltage systems. these level translators have two supply voltages, v l and v cc , which set the logic levels on the input and output sides of the translator. when used to transfer data from the i/o v l to the i/o v cc ports, input signals referenced to the v l supply are translated to output signals with a logic level matched to v cc . in a similar manner, the i/o v cc to i/o v l translation shifts input signals with a logic level compatible to v cc to an output signal matched to v l . the NLSX5002 translator consists of bi ? directional channels that independently determine the direction of the data flow without requiring a directional pin. one ? shot circuits are used to detect the rising or falling input signals. in addition, the one ? shots decrease the rise and fall times of the output signal for high ? to ? low and low ? to ? high transitions. input driver requirements auto ? sense translators such as the NLSX5002 have a wide bandwidth, but a relatively small dc output current rating. the high bandwidth of the bi ? directional i/o circuit is used to quickly transform from an input to an output driver and vice versa. the i/o ports have a modest dc current output specification so that the output driver can be over driven when data is sent in the opposite direction. for proper operation, the input driver to the auto ? sense translator should be capable of driving 5 ma of peak output current. the bi ? directional configuration of the translator results in both input stages being active for a very short time period. although the peak current from the input signal circuit is relatively large, the average current is small and consistent with a standard cmos input stage. enable input (en) the NLSX5002 translator has an enable pin (en) that provides tri ? state operation at the i/o pins. driving the enable pin to a low logic level minimizes the power consumption of the device and drives the i/o v cc and i/o v l pins to a high impedance state. normal translation operation occurs when the en pin is equal to a logic high signal. the en pin is referenced to the v l supply and has over ? voltage tolerant (ovt) protection. uni ? directional versus bi ? directional t ranslation the NLSX5002 translator can function as a non ? inverting uni ? directional translator. one advantage of using the translator as a uni ? directional device is that each i/o pin can be configured as either an input or output. the configurable input or output feature is especially useful in applications such as spi that use multiple uni ? directional i/o lines to send data to and from a device. the flexible i/o port of the auto sense translator simplifies the trace connections on the pcb. power supply guidelines the values of the v l and v cc supplies can be set to anywhere between 0.9 and 4.5 v. design flexibility is maximized because v l may be either greater than or less than the v cc supply. in contrast, the majority of the competitive auto sense translators has a restriction that the value of the v l supply must be equal to less than (v cc ? 0.4) v. the sequencing of the power supplies will not damage the device during power ? up operation. in addition, the i/o v cc and i/o v l pins are in the high impedance state if either supply voltage is equal to 0 v. for optimal performance, 0.01 to 0.1 f decoupling capacitors should be used on the v l and v cc power supply pins. ceramic capacitors are a good design choice to filter and bypass any noise signals on the voltage lines to the ground plane of the pcb. the noise immunity will be maximized by placing the capacitors as close as possible to the supply and ground pins, along with minimizing the pcb connection traces. the NLSX5002 translators have a power down feature that provides design flexibility. the output ports are disabled when either power supply is off (v l or v cc = 0 v). this feature causes all of the i/o pins to be in the power saving high impedance state.
NLSX5002 http://onsemi.com 12 package dimensions uqfn8 1.4x1.2, 0.4p case 523as issue a ?? ?? a b e d bottom view b e 6x 0.10 b 0.05 a c c note 3 2x 0.10 c pin one reference top view 2x 0.10 c a a1 (a3) 0.05 c 0.05 c c seating plane side view l2 1 2 4 8 dim min max millimeters a 0.45 0.55 a1 0.00 0.05 a3 0.13 ref b 0.15 0.25 d 1.40 bsc l1 ??? 0.15 e 1.20 bsc e 0.40 bsc l 0.20 0.40 detail b detail a *for additional information on our pb ? free strategy and soldering details, please download the on semiconductor soldering and mounting t echniques reference manual, solderrm/d. soldering footprint* pitch 0.55 7x dimensions: millimeters 1 6 l 0.45 1.61 1.40 0.40 l2 0.30 0.50 0.25 8x l1 detail a l alternate constructions l ??? ??? ??? m m on semiconductor and are registered trademarks of semiconductor components industries, llc (scillc). scillc reserves the right to mak e changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for an y particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, in cluding without limitation special, consequential or incidental damages. ?typical? parameters which may be provided in scillc data sheets and/or specifications can and do vary in different a pplications and actual performance may vary over time. all operating parameters, including ?typicals? must be validated for each customer application by customer?s technical e xperts. scillc does not convey any license under its patent rights nor the rights of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the scillc prod uct could create a s ituation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indem nify and hold scillc and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney f ees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that scillc was neglig ent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner. NLSX5002/d publication ordering information n. american technical support : 800 ? 282 ? 9855 toll free usa/canada europe, middle east and africa technical support: phone: 421 33 790 2910 japan customer focus center phone: 81 ? 3 ? 5817 ? 1050 literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 303 ? 675 ? 2175 or 800 ? 344 ? 3860 toll free usa/canada fax : 303 ? 675 ? 2176 or 800 ? 344 ? 3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your loca sales representative

▲Up To Search▲

Price & Availability of NLSX5002

	To Download NLSX5002 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .